Maple Leaf Appliance Repair

Dishwasher Not Draining Edmonton Repair — Maple Leaf Appliance Repair

Back to Blog
·Dishwasher Repair

Dishwasher Not Draining? Here's Why (And How We Fix It in Edmonton)

A dishwasher that won't drain usually traces back to one of a handful of culprits — a clogged filter, a blocked drain hose, a jammed pump impeller, or a failed drain pump motor. Here are the most common causes our Edmonton technicians find, and what's safe to check yourself before booking service.

Standing Water in the Bottom of the Dishwasher

Finding an inch or two of standing water in the bottom of your dishwasher after a cycle is the most common drainage complaint our Edmonton technicians see. The water is supposed to be pumped out through the drain hose at the end of the cycle, so if it's still there, something is blocking or bypassing that path. The good news is that the most common cause — a clogged filter — is something you can check and clear yourself in about five minutes.

The filter assembly sits at the bottom of the dishwasher tub, usually under the lower spray arm. On most modern dishwashers it's a two-piece unit: a coarse mesh pre-filter that catches large food particles, and a fine cylindrical filter underneath that catches smaller debris. Both need to be rinsed under running water and scrubbed gently with a soft brush every few weeks. A filter that's been neglected for months can become so clogged that water can't pass through it at all, leaving a full inch of standing water after every cycle.

If the filter is clean and water is still pooling, the next place to check is the drain hose. The drain hose runs from the pump at the bottom of the dishwasher to either the sink drain or an air gap fitting on the countertop. It should form a high loop under the sink — the top of the loop should be as high as possible under the counter — to prevent backflow from the sink drain into the dishwasher. A hose that has slipped down, kinked, or become clogged with grease and debris will prevent proper drainage even when the pump is working correctly.

Dishwasher Drain Pump Failure

When the filter and drain hose are clear but the dishwasher still won't drain, the drain pump is the next suspect. The drain pump is a small electric motor with an impeller that forces water out through the drain hose at the end of the cycle. When the pump motor fails, the impeller seizes, or a piece of broken glass or a food bone jams the impeller, the pump can't move water and it stays in the tub. You can often hear the difference: a working pump makes a steady humming sound during the drain phase; a failed or jammed pump either makes no sound at all or produces a loud grinding or buzzing.

A jammed impeller is worth checking before assuming the pump motor has failed. Accessing the pump requires removing the lower spray arm, the filter assembly, and sometimes the lower rack, then unclipping the pump cover. Once the cover is off, you can often see and remove the obstruction — a broken piece of glass, a small bone, or a twist tie that found its way past the filter. Clearing the jam restores drainage without any parts replacement.

A pump motor that has burned out needs to be replaced. On most dishwashers the drain pump is a separate component from the wash pump, so replacing it doesn't require pulling the entire pump assembly. The repair typically takes 45–60 minutes for a technician and is one of the more cost-effective dishwasher repairs — the part itself is usually $60–$120 depending on the brand, and the labour is straightforward.

Check Valve and Solenoid Faults

The check valve (also called a drain valve or flapper valve) sits at the outlet of the drain pump and prevents water from flowing back into the tub after the pump stops. When the check valve fails in the open position, water that was successfully pumped out can siphon back into the tub, leaving a small amount of standing water — typically less than an inch — after the cycle ends. This is different from a pump failure, where the water never leaves at all.

A small amount of water — roughly a cup or less — remaining in the bottom of the dishwasher after a cycle is actually normal on many models. Manufacturers design the sump to retain a small amount of water to keep the door seal from drying out. If you're seeing just a thin film of water at the very bottom of the sump, check your owner's manual before calling for service — it may be intentional.

Some older dishwashers use a solenoid-operated drain valve rather than a separate drain pump. The solenoid opens a valve at the bottom of the tub to allow water to drain by gravity or be pushed by the wash pump. When the solenoid coil burns out or the valve mechanism sticks, the valve stays closed and water can't drain. Testing the solenoid requires a multimeter to check for continuity; a reading of infinite resistance confirms the coil has failed and needs replacing.

Door Latch, Float Switch, and Control Board Issues

If the dishwasher door latch doesn't engage fully, the control board may not advance the cycle to the drain phase at all — the machine stops mid-cycle and leaves water in the tub. This is more common on older dishwashers where the latch mechanism has worn. The door switch is easy to test: close the door firmly and listen for the click of the latch engaging. If the cycle won't start or stops early, a faulty door latch or door switch is worth checking before assuming a drainage fault.

The float switch is a small plastic dome at the bottom of the dishwasher tub that rises with the water level and cuts off the fill valve when the tub is full. When the float gets stuck in the raised position — usually because debris has built up around it — the control board thinks the tub is always full and may prevent the drain cycle from completing. Lifting the float by hand and cleaning around its base often resolves this.

A faulty control board can also cause drainage failures by not sending the drain signal to the pump at the end of the cycle. Control board failures are less common than mechanical faults, but they do occur — particularly on dishwashers that have experienced a power surge or water ingress near the control panel. A technician can confirm a control board fault by testing whether the drain pump receives voltage during the drain phase; if it doesn't, the board is the likely culprit.

Dishwasher Drain Error Codes: Samsung, Bosch, LG and More

Samsung dishwashers display a 5C or 5E error code (sometimes shown as SC) when the control board detects a drainage fault — the cycle ran but the water level sensor didn't confirm the tub emptied. The most common cause is a clogged filter or kinked drain hose, so start there before replacing any parts. An OC or 0C code indicates an overflow condition, which can also prevent draining if the float switch is stuck in the raised position.

Bosch dishwashers show an E24 error code for a drain blockage — the pump ran but water didn't drain within the expected time. E25 indicates the drain pump is blocked or the pump cover is not seated correctly. On Bosch models, the pump cover is a quarter-turn cap at the bottom of the tub; if it's not fully locked, the pump can't build pressure and the E25 code appears. LG dishwashers use an OE code for drainage errors, which covers everything from a clogged filter to a failed drain pump motor.

Whirlpool and Maytag dishwashers typically show an F8 E1 or F8 E2 code for water level and drainage faults. Frigidaire and Electrolux models display an ER code followed by a number; ER 3 specifically indicates a drain motor fault. In all cases, clearing the filter and checking the drain hose for kinks or blockages should be the first step — these simple fixes resolve the majority of drain error codes without any parts replacement.

When to Call a Professional

If you've cleared the filter, confirmed the drain hose is unkinked and properly looped, and the dishwasher still won't drain, the problem is most likely a failed drain pump, a seized impeller, a faulty check valve, or a control board that isn't triggering the drain cycle. These repairs require disassembly and component testing that's best left to a technician — attempting them without the right tools can damage the pump housing or the tub seal.

Maple Leaf Appliance Repair services all major dishwasher brands including Samsung, Bosch, LG, Whirlpool, Maytag, GE, Frigidaire, Electrolux, KitchenAid, Miele, and Kenmore. We serve Edmonton and the surrounding communities including St. Albert, Sherwood Park, Spruce Grove, Leduc, Fort Saskatchewan, Beaumont, Devon, Stony Plain, Morinville, Gibbons, and Calmar, and every repair is backed by our 90-day parts and labour warranty.

Call us at (780) 800-6629 or book online at mapleleafappliances.ca to schedule your dishwasher repair. We're available Monday through Sunday, 6 AM to 10 PM, with same or next-day appointments across the Edmonton area.

Need a dishwasher repair in Edmonton?

Same-day service · 90-day warranty

Have any question? Call Us

(780) 800-6629BOOK ONLINE